# Reverse Osmosis Storage Tank Replacement: Which 1/4 in Tank Fits, Usable Gallons and the Factory Precharge by Maker > Standard RO tanks: 1/4 in NPT, 4 gal nominal, about 3.2 gal usable, factory precharge 5 to 10 psi by maker. Which tank fits, and how to swap it. | | | |---|---| | Source | https://ownerspec.com/water/parts/reverse-osmosis-storage-tank-replacement-and-precharge/ | | Publisher | OwnerSpec (https://ownerspec.com/) | | Published | 2026-09-13 | | Updated | 2026-09-13 | | Facts verified | 2026-09-13 | | Disclosure | Contains affiliate links. OwnerSpec may earn a commission at no cost to the reader. | --- ## Short answer A standard under-sink reverse osmosis storage tank is a 4 gallon nominal tank on a 1/4 in NPT stem, and four current models fit: the iSpring T32M, the APEC TANK-4, Express Water's RO132-TNK and the GWS PA-E RO-132, which is 4.8 gallons nominal. Nominal is not usable: APEC's TANK-4 table gives 1.9 gallons usable at 20 psi line pressure and 3.2 gallons at 60 psi, and iSpring rates the T32M at up to 3.2 gallons holding. The spec that must match is the 1/4 in thread on the tank valve. The spec that differs by maker is the factory air precharge: 5 psi for APEC, 5 to 8 psi for GWS, 7 to 10 psi for iSpring, so an empty replacement is set to its own maker's figure, not to a number copied from the old tank. The 14 gallon APEC TANK-14 uses a 3/4 in thread and does not fit a 1/4 in valve. No maker publishes a service life for the tank. ## Fact sheet - **Answer:** A standard under-sink RO storage tank is 4 gallons nominal with a 1/4 in NPT stem; the iSpring T32M, APEC TANK-4, Express Water RO132-TNK and GWS PA-E RO-132 all fit that valve, and iSpring's and APEC's pages put usable volume at about 3.2 gallons. Factory precharge is the maker's figure, not a universal one: 5 psi APEC, 5 to 8 psi GWS, 7 to 10 psi iSpring. - **Applies to:** RO storage tank, 1/4 in NPT class (T32M, TANK-4, RO132-TNK, PA-E RO-132, T55M); APEC TANK-14, 3/4 in NPT class - **Compatibility basis:** iSpring T32M and T55M product pages, APEC TANK-4 and TANK-14 pages, Express Water RO132-TNK page and the GWS PA-E RO tank spec sheet, read 2026-09-13 - **Assumptions:** Usable gallons come from APEC's TANK-4 table and iSpring's holding figures; GWS publishes no drawdown table for the RO-132.; No NSF, WQA or IAPMO listing-database entry was reachable for any tank SKU, so every certification on this page is the maker's own claim.; None of the four makers publishes a service life for the tank or a procedure for checking and resetting the air charge. - **Method:** Published specifications copied from each maker's page or PDF and compared on capacity, connection, precharge, dimensions and certification claim; no tank was tested. - **Primary source:** [APEC Water Systems, TANK-4 residential RO tank page (usable-gallon table, precharge, thread, dimensions)](https://www.apecwater.com/products/ro-tanks-residential) (manufacturer or vendor document) - **Facts verified:** 2026-09-13 - **Last updated:** 2026-09-13 - **Canonical URL (cite this):** https://ownerspec.com/water/parts/reverse-osmosis-storage-tank-replacement-and-precharge/ If the faucet trickles and the tank is light and empty, this is the wrong page: the [iSpring RCC7](/water/parts/ispring-rcc7-replacement-filters/) and [APEC ROES-50](/water/parts/apec-roes-50-replacement-filters/) parts pages carry the membranes and pre-filters that cause that. ## Which tank fits a standard under-sink RO system? Thread and capacity decide fit, not brand: APEC's ROES-50 page lists its stock tank at 4 gallons and 11 x 11 x 15 in, the footprint of the TANK-4 and the T32M, and every tank below threads onto the same 1/4 in valve. The figures are the makers' published specifications, read 2026-09-13; nothing was tested. | Tank | Nominal | Usable (maker's figure) | Connection | Factory precharge | Size and weight | Certification | |---|---|---|---|---|---|---| | iSpring T32M | 4 gal | Up to 3.2 gal holding | 1/4 in NPT, valve included | 7 to 10 psi | 11 x 11 x 14 in, 8.10 lb | NSF/ANSI 61, listed per iSpring's page | | APEC TANK-4 | 4 gal | 1.9 gal at 20 psi, 3.2 gal at 60 psi, 3.42 gal at 70 psi | 1/4 in MPT, valve sold separately | 5 psi | 11 in D x 15 in H, 10 lb | CE approved per APEC's page; no NSF number stated | | Express Water RO132-TNK | 4 gal | Up to 3.2 gal | 1/4 in quick connect, valve included | Not published; 10 psi stated as the maximum | 15 x 12 x 12 in; weight not published | "NSF certified" per Express Water's page; no standard number | | PA-E RO-132 (GWS, sold under the PAE badge) | 4.8 gal (18 L) | Not published | 1/4 in NPT, valve sold separately | 5 to 8 psi (0.3 to 0.5 bar) | 351 x 279 mm, 3.5 kg | Logos on the sheet's cover only; GWS says certification varies by model | Maximum working pressure is 100 psi on iSpring's T32M page, Express Water's RO132-TNK page and the GWS sheet; APEC publishes none for the TANK-4. ## What else fits the same valve? The 1/4 in class stops at 5.5 gallons; APEC's 14 gallon tank moves to a 3/4 in stem with its own valve. The [RO GPD and tank size calculator](/water/calculators/reverse-osmosis-gpd-tank-size-calculator/) says whether your daily draw needs it. | Alternative | Same 1/4 in thread? | Capacity | What differs | |---|---|---|---| | iSpring T55M | Yes, 1/4 in NPT | 5.5 gal nominal, 4.0 gal holding | 12 x 12 x 16 in and 9.00 lb per iSpring's page, 2 in taller than the T32M; same 7 to 10 psi precharge | | APEC TANK-14 | No, 3/4 in MPT | 14 gal nominal, 6.1 gal usable at 20 psi to 10.7 gal at 70 psi | 15 3/8 in D x 22 7/8 in H, 30 lb, 5 psi precharge per APEC's page; Amazon sells it bundled with the 3/4 in valve | | John Guest 1/4 in tank ball valve (PPSV500822W, listed by IPW Industries) | Yes, 1/4 in NPTF x 1/4 in tube | Valve only | Rated 150 psi at 70 F per APEC's page; the same part number APEC sells | | APEC 3/4 in NPTF ball valve | No, 3/4 in NPTF x 3/8 in tube | Valve only | APEC's valve for its 14 and 20 gallon tanks | On a same-thread swap the old valve moves to the new tank; replace it only when the quick-connect collet is damaged. ## What precharge should the new tank carry? The precharge is the air pressure behind the bladder in an empty tank: 5 psi on APEC's TANK-4 and TANK-14, 0.3 to 0.5 bar (5 to 8 psi) on the GWS sheet, 7 to 10 psi on iSpring's T32M and T55M. Express Water prints 10 psi only as a maximum, not a shipped setting. No maker document in the Sources list describes how to check or reset that charge, so this page prints no procedure. The figures still settle the diagnosis: a tank that stays heavy while the faucet trickles, and reads well under its precharge once drained, has lost its air charge; one already at that figure points back at the membrane. ## How do you replace the tank? APEC's tank replacement PDF (V2.1) gives the sequence; it is the same job on any 1/4 in tank. 1. Shut off the feed water and open the RO faucet until the old tank is drained. 2. Close the tank ball valve. 3. Press in and hold the quick-connect collet ring, then pull the tubing out. 4. Unscrew the valve from the old stem, counterclockwise. 5. Wrap the new stem with Teflon tape and screw the valve back on. 6. Reconnect, open the feed, let the tank fill, and drain the first tankful. No maker publishes a service life for the tank: the trigger is a lost air charge or a leak at the stem, not a calendar. ## Which tank should you buy, and who should skip it? The iSpring T32M carries a written NSF/ANSI 61 claim on the maker's page, valve included. Skip it if you prefer a narrow precharge window: 7 to 10 psi is the widest range here. The APEC TANK-4 has the easiest 5 psi setpoint to hit, and is the tank APEC's usable-gallon table describes. Skip it for a standard number: CE approved only, no NSF number, separate valve. The Express Water RO132-TNK ships with its quick-connect valve and the same 3.2 gallon figure as the T32M. It lacks a published setpoint, a factory figure, and a weight spec. The PA-E RO-132 is the largest of the 1/4 in class at 4.8 gallons nominal, listed on Amazon under the PAE reseller badge, not GWS's name. GWS publishes no usable-gallon figure and no per-SKU certification. **Gauge first, tank second** Every figure above is a maker's published specification. No maker publishes a service life or a check procedure for the air charge, so gauge the drained tank before it goes in the cart. At the maker's precharge with the faucet still trickling, the tank is not the fault. Well under it, buy the T32M for the written NSF/ANSI 61 claim or the TANK-4 for the 5 psi setpoint, and keep the old valve. ## The picks - **iSpring T32M**: Standard 1/4 in swap with a written NSF/ANSI 61 claim (4 gal nominal, up to 3.2 gal holding, 1/4 in NPT, 7 to 10 psi precharge, 11 x 11 x 14 in, valve included; NSF/ANSI 61 per iSpring's page) Amazon: https://www.amazon.com/dp/B00439MYYE/?tag=ownerspec-20 - **APEC TANK-4**: Standard 1/4 in swap with the easiest 5 psi setpoint (4 gal nominal, 1.9 to 3.42 gal usable at 20 to 70 psi, 1/4 in MPT, 5 psi precharge, 11 in D x 15 in H, 10 lb; valve sold separately) Amazon: https://www.amazon.com/dp/B00LU28SHE/?tag=ownerspec-20 - **Express Water RO132-TNK**: Standard swap with the quick-connect valve in the box (4 gal nominal, up to 3.2 gal, 1/4 in quick connect, 100 psi maximum working pressure, 15 x 12 x 12 in; no factory precharge figure published) Amazon: https://www.amazon.com/dp/B00Q798N8E/?tag=ownerspec-20 - **PA-E RO-132 (GWS, sold under the PAE badge)**: Largest of the 1/4 in class by nominal volume (4.8 gal (18 L) nominal, 1/4 in NPT, 5 to 8 psi precharge, 351 x 279 mm, 3.5 kg, 100 psi maximum; no usable-gallon figure published) Amazon: https://www.amazon.com/dp/B015DO1LSC/?tag=ownerspec-20 - **iSpring T55M**: Same 1/4 in valve, 2 in taller, more drawdown (5.5 gal nominal, 4.0 gal holding, 1/4 in NPT, 7 to 10 psi precharge, 12 x 12 x 16 in, 9.00 lb) Amazon: https://www.amazon.com/dp/B01CES39N0/?tag=ownerspec-20 - **APEC TANK-14 with 3/4 in valve**: High-draw setups only; does not fit a 1/4 in valve (14 gal nominal, 6.1 to 10.7 gal usable at 20 to 70 psi, 3/4 in MPT, 5 psi precharge, 15 3/8 in D x 22 7/8 in H, 30 lb; sold bundled with the 3/4 in ball valve on Amazon) Amazon: https://www.amazon.com/dp/B0C2HC1C4H/?tag=ownerspec-20 - **John Guest 1/4 in tank ball valve (PPSV500822W, IPW Industries listing)**: Replacement valve for the 1/4 in class, collet damaged (1/4 in NPTF x 1/4 in tube OD, rated 150 psi at 70 F per APEC's page; the same John Guest part number APEC sells) Amazon: https://www.amazon.com/dp/B0C24ZV17M/?tag=ownerspec-20 - **APEC 3/4 in NPTF tank ball valve, 3/8 in output**: Valve for the 14 and 20 gallon tanks (3/4 in NPTF thread, 3/8 in tube output; APEC's valve for its 14 and 20 gallon tanks) Amazon: https://www.amazon.com/dp/B01MF5IOLP/?tag=ownerspec-20 ## Frequently asked questions ### What connection size does a standard RO storage tank use? The 1/4 in NPT tank stem is the standard for the under-sink class: iSpring lists it on the T32M and T55M pages, APEC on the TANK-4 page as 1/4 in male pipe thread, and GWS in its RO-122 and RO-132 table. APEC's 14 gallon TANK-14 steps up to a 3/4 in male pipe thread and needs its own 3/4 in valve. ### How much of a 4 gallon RO tank can you actually use? Less than 4 gallons, because the air side of the bladder takes part of the volume. APEC's TANK-4 table gives 1.9 gallons usable at 20 psi line pressure, 3.2 gallons at 60 psi and 3.42 gallons at 70 psi. iSpring rates the T32M at up to 3.2 gallons holding and the T55M at 4.0 gallons holding. ### What factory precharge should a new RO tank have? The maker's own figure, which is not the same across brands. APEC states 5 psi for the TANK-4 and the TANK-14, the GWS spec sheet states 0.3 to 0.5 bar, which it converts to 5 to 8 psi, and iSpring states 7 to 10 psi for the T32M and T55M. Express Water prints 10 psi only as a maximum, not as a shipped setting. ### Does a bigger tank make more RO water per day? No. Tank size changes how many gallons you can draw before the faucet slows and how long the refill takes; the membrane's rated output depends on feed pressure and temperature. APEC's TANK-14 stores 6.1 to 10.7 usable gallons against the TANK-4's 1.9 to 3.42, over the same 20 to 70 psi, without changing the system's GPD. ### How do you replace an RO storage tank? APEC's replacement instructions: shut the feed water, drain the tank through the RO faucet, close the tank ball valve, press the quick-connect collet ring in and pull the tubing out, unscrew the valve counterclockwise, wrap the new tank's threaded stem with Teflon tape, screw the valve back on, reconnect, refill, and drain the first full tank before drinking from the second. ## Sources - [Global Water Solutions USA, PA-E and TankPAC RO tanks spec sheet (PDF)](https://gwsusa.com/wp-content/uploads/RO-Tanks-GWSUSA-web-1.pdf) (manufacturer or vendor document) - [iSpring, T32M 4 gallon pressurized storage tank product page](https://www.ispringfilter.com/tanks/ispring-t32m-pressurized-water-storage-tank-with-with-ball-valve-for-reverse-osmosis-ro-systems-4-gallon) (manufacturer or vendor document) - [iSpring, T55M 5.5 gallon pre-pressurized storage tank product page](https://www.ispringfilter.com/tanks/ispring-t55m-55-gallon-residential-pre-pressurized-water-storage-tank-for-reverse-osmosis-ro-systems) (manufacturer or vendor document) - [APEC Water Systems, TANK-4 residential RO tank page (usable-gallon table, precharge, thread, dimensions)](https://www.apecwater.com/products/ro-tanks-residential) (manufacturer or vendor document) - [APEC Water Systems, TANK-14 14 gallon pressurized tank page](https://www.apecwater.com/products/tank-14-gallon-pressurized-3-4-outlet) (manufacturer or vendor document) - [Express Water, TankRO 4 gallon RO expansion tank (RO132-TNK) product page](https://www.expresswater.com/products/tankro-4-gallon-ro-expansion-tank) (manufacturer or vendor document) - [APEC Water Systems, John Guest 1/4 in tank ball valve page](https://www.apecwater.com/products/jg-tank-ball-valve) (manufacturer or vendor document) - [APEC Water Systems, 3/4 in NPTF tank ball valve with 3/8 in output for 14 and 20 gallon tanks](https://www.apecwater.com/products/tank-ball-valve-3-4-nptf-3-8-output-for-14-gallon-tank) (manufacturer or vendor document) - [APEC Water Systems, ROES-50 product page (stock tank size)](https://www.apecwater.com/products/roes-50) (manufacturer or vendor document) - [APEC Water Systems, How to Replace the RO Pressure Tank, V2.1 (PDF)](https://cdn.shopify.com/s/files/1/0674/1304/9597/files/Instru-Tank-Replacement-V2.1_Watermark.pdf) (manufacturer or vendor document) --- Citation: OwnerSpec, "Reverse Osmosis Storage Tank Replacement: Which 1/4 in Tank Fits, Usable Gallons and the Factory Precharge by Maker", https://ownerspec.com/water/parts/reverse-osmosis-storage-tank-replacement-and-precharge/, facts verified 13 September 2026. Canonical citation target: the URL above (the public HTML page), not this Markdown representation. Reuse: quoting with attribution and a link is permitted. See https://ownerspec.com/legal/terms/.